Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are long-lasting, durable and easy to maintain. They are not susceptible to get rotten or rusty like aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will help prevent costly repairs and improve energy efficiency.

1. Broken Glass

The damaged glass in your windows can cause severe damage to your home and even be fatal. It is important to make sure that your windows are in good shape.

Single-pane windows are relatively easy to replace and will usually fit into the frames that were previously in use very easily. If you have double-paned windows which are joined by internal beading, it will be difficult to remove and replace the old panes. In this case you'll need locate some plastic spacers to aid the new pane in being able to fit properly into the frame of the window.

Wearing protective eyewear and thick gloves is a must if you plan to remove the glass by yourself. You should also lay down a dropcloth prior to you begin working on the window panes, so that any shards of glass fall onto the fabric, not onto the floor and could be trampled under.

It's a great idea tape the gap once the glass is removed. This will stop water and drafts from entering your property until a professional is able to repair the window. It also acts as an obstruction to prevent intruders from getting into your home. If the gap is large, you might think about the security door repair with an integrated window as it will provide the best of both worlds.

2. Sagging

uPVC windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber sash windows. As time passes, they may develop a number of problems that include sliding. A window that is sagging can cause problems with light, draughts, and even security. It is crucial to act immediately if you notice your uPVC windows are sliding.

To fix a sagging window you can try repositioning the hinges. First, you'll need to open the windows so you can reach the frame. Then, remove both the hinges at the top and bottom using a screwdriver, and then adjust them clockwise or counter-clockwise. Once you've adjusted the hinges, close your window and test it for fitting. If you're satisfied with the fit of the window, tighten the screws to keep them in place.

If you are unable to move the hinges, you might need to replace the seal. Rubber seals can dry out and lose their elasticity over time, which causes them to loose their elasticity. If this happens, it's essential to replace the seal as soon as you can to ensure that your uPVC windows remain watertight and draught-proof.

uPVC handles may also become loose. Often it is due to screws that have become loose over time. However, it could occur because the handle mechanism has worn out. Fortunately, it's easy to fix the loose uPVC window repair near me handle yourself. First, you'll need to shut the window and do a test fitting. The corner joints of the sash need to be aligned with the casing joint. If it doesn't, you can use a screwdriver or a wrench to loosen the handle and then turn the mechanism back into its original position.

3. Water Leaks

It is essential to take action if wake up every morning to find a smoky wall and wet floors. Water leaks from windows not only lead to the degrading of the structure of your home but also hamper your efforts to regulate the temperature inside your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

It is a fairly easy fix that can be completed by any skilled DIYer. Depending on the severity of the problem the caulking that was used up may need to be removed before a new layer is applied. When it comes to uPVC repair double glazed windows, it is important to avoid 'over-caulking'. This will make your window more difficult to clean and lower its energy efficiency.

Verify that the drainage holes are free of debris in them, and also that the sill pan is angled correctly to drain away from the window. In more serious cases you might have to consider replacing the window.

Other signs of long-term water leakage are sills that are rotten and the appearance of black spots of mold on the wall near the window. This is a fungus that thrives in damp conditions and can quickly spread throughout the home.

If the leakage is occurring between the double glazed repairs near me-glazed glass, it is more likely that the issue is more with the seal rather than the frame. A uPVC specialist can fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges may be to blame if your uPVC window is difficult to open or if it opens in the breeze. They can be easily repaired by any DIYer who is skilled and can usually be done within a few minutes.

Most households in the UK will have top-hung or side-hung uPVC windows that have hinges and, like all mechanical parts, they will wear out over time. It's very simple to change a window hinge however it is simpler if you have someone to help you hold the frame.

Check that the uPVC hinges are closed and open in the correct direction. You can do this by looking for the arrow on each hinge, this indicates which way the window should open.

Faulty window hinges could be the result of incorrectly opening the window in a particular way or by improper installation in the factory. Sending us a photo through our website can often solve the issue. We are more than happy to provide advice.

Regular lubrication of the hinges is also necessary. This can be accomplished by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It also decreases the possibility of a window getting stuck and stop corrosion. This must be done at a minimum every year. WD40 and other solvent-based lubricants should not be used since they could damage your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by different factors. The hinges may also become misaligned due to wear, which can cause gaps where the sash and frame meet. If they are damaged beyond repair, it might be necessary to have them realigned. In addition, the interlock could also become disaligned. This happens on the hinge side and could require to be cleaned. In some cases, it may be necessary to replace these.

The seals may wear out or be damaged over time, allowing air to escape. Replacing these with high-quality weatherstripping can help stop draughts. Replace the windows made of upvc with low-emissivity glasses. This will help control indoor temperatures and decrease the risk of draughts.

Lastly, one of the most effective ways to cut down on the draughts in your home is to use a draught excluder. These are typically made of fabric filled with some sort of filler and can be positioned on the windowsill on top. They will help stop cold air from entering and keep your home warm and cozy!

Your windows made of upvc will keep providing excellent insulation and security in your home by performing regular maintenance and repairs. It is essential to remember that all windows eventually wear out and it is cheaper to replace them rather than repair them. If you are experiencing issues with your Upvc window you should consult a professional as soon as you can.