Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinct SUV feel to it thanks to its bigger dimensions, and the ride on 19-inch wheels in Ti and ST-L models can be a bit spongy at times. The front tyres of Qashqai may also lose grip on bumpy surfaces, and its CVT can sometimes display a wrist-flexing torque steering.

It is usually caused by an unresponsive coin battery that can be easily replaced in minutes. Make sure the new battery is of the same voltage, size and specification.

Water Damage

One of the main reasons why a lost nissan key key fob gives the "key ID is not correct" message is due to water damage. The rubber seals on the key fob protect the electronic chip, but prolonged moisture exposure can cause it to stop working effectively. This is often the case when you've dropped your key fob in the ocean or into a swimming water pool, but it could occur if it becomes wet due to rain or soapy hands.

If your key fob is exposed to water for an extended period of time, it could need to be cleaned using isopropyl alcohol or an electronic cleaner. In addition, it may need to be taken to an expert to repair or replace it.

If your key fob is in need to be replaced, it's quite simple to do. Make sure you have the correct multipack (CR2032, 3V). Unlock the front and rear cases with a flathead screwdriver. It is necessary to remove the metal retaining clips and then push out the old battery, and then put in the new one. Reassemble the fob and replace the mechanical key. Check to see if it functions correctly. If it does not then you'll need to go to your local nissan juke key fob replacement dealer or an expert locksmith to replace the chip that controls the key. Fortunately the chip isn't typically damaged by exposure to water, so this should not be a huge expense.

Dead Coin Battery

The coin battery is another common reason for why your Nissan Qashqai remote key fob won't work. The batteries typically last for 3-5 years, but they can become depleted over time, particularly if the fob is frequently dropped. You can replace the battery but be sure to use the same voltage and same size as the previous. If you use a different battery, it can cause the key to have an incorrect key ID which could prevent it from paired with your vehicle.

The most effective method to replace the battery in a nissan micra key programming Qashqai key fob is by prying open the fob with the small screwdriver with a flat-head. Push in the screwdriver in tiny notch at the bottom of the fob, and turn it around gently to separate the two halves of the key fob. Then, take out the old CR2025 button cell battery and replace it with an alternative one after taking note of its location in the fob.

Check the terminals for any water damage or dirt before installing the new battery. If there is, clean the terminals using a small amount isopropyl ethanol. Make sure that the pole cables are properly connected. They should be connected to both the positive and negative poles of your battery.

Troubleshooting

If your nissan replacement keys Qashqai's keys fob stops working after being exposed to clean water from the tap or rain, this could indicate that there's an issue with the internal chip. You'll need a new keyfob if you are unable to fix the issue by changing the battery. If the key fob has stopped working after you dropped it, it is likely that the chip inside was damaged. It is possible to get the key fob to work once again if it is removed and clean the chip with paper towel and isopropyl alcohol, then put it back in.

Key ID Incorrect is a typical error that can be seen on the dashboard of your car. This means that the vehicle cannot recognize the key fob, and will not allow it to start the engine. The problem can be caused by a variety of things, including water damage, undetectable malfunctions in the circuitry of the key fob, or RFID interference.

The key fob won't work when the 12 volt batteries are not working or provide enough electric current. This will affect the remote keyless system as well as central locking of your Nissan Key replacement program Qashqai, as well as making it impossible to start the engine with the key fob (if equipped with Intelligent Key). Examine the batteries on the key fob if you're not able to lock and unlock your door manually. Try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob was not submerged into saltwater, it should be able be revived with a simple wash of clean water. You can also clean the electronic component using isopropyl or electronic cleaner. If these methods don't work then it might be time to replace the entire key fob with a new one.

If your Nissan Intelligent Key still does not work, there could be a connection issue between it and the vehicle. Start by turning the ignition key but not activating the vehicle. Continue this process until you see the warning lights flash twice. Turn off your vehicle and remove the key.

Open the fob compartment in your vehicle's fob compartment. This is usually located in a door jamb on the handle for the driver's door or underneath an armrest. Find the small button marked "program" and press it. You will hear a sound when the process is completed.

It's time to test your Intelligent Key to the test. Use all the buttons on the key while standing at a distance away from the car. If the lights flash or the horn sounds, the key is connected to the Nissan. You can also test it near the Nissan.