Replacement UPVC Door Handles

You can find the perfect handle for your door, whether you're replacing your existing handles or adding additional security. The Upvc double glazing windows handles are simple to install and have the minimum 92mm center distance of multipoint locks.

The most important measurements to take into consideration are backplate fixing centres as well as lever/key hole dimensions. Check these carefully against your existing marks before ordering.

Lever/Pad

Lever pad handles are made up of a lever on one side and a handle that is shaped like a paddle on the other. They are designed to be used with key wind locks. However they can be affixed to multipoint split spindle door locks.

Our range of upvc handle for double glazed window lever pads are available in a range of finishes. They will be listed in the drop-down list after you have selected the perfect handle for your door. Not all styles of handle are available in every finish and you should always look over the sizes and technical drawings for the particular product you want to make sure that you can get the correct size and fitting.

When you are choosing a new set of upvc lever pad door handles it is important to ensure that they correspond to the PZ (distance between the spindle of the handle and the center of the cylinder hole) of your existing multipoint door locks, as these need to be in line for the doors to remain locked, either from the inside or the outside. The handles we sell are designed to work with the majority of standard cylinder locks, however it is advisable to double glazing handles-check before ordering.

If you are looking to upgrade to dual spindle levers, you will need to remove the handles that are currently in use and then disassemble the lock case. This will require an additional split inline cylinder. You can purchase these separately. We have included a technical diagram in the images of each product.

After you have removed the screws that hold the handle on your door, it is an ideal idea to loosen them and inspect the mechanism to see how it's performing. It is possible that you will need to loosen the screws further in the event that they are not tight. After that, you can remove the old handle and spindle and install your new upvc door handle. It is crucial to make sure that the handle is in the correct position before screwing it into place. You can do this by placing your finger between the frame of the door, and the handle to ensure that it is level.

Lever/Lever

The lever door handles are used to operate a multi-point lock with the Euro Lock Handles cylinder. They are found on a variety of double glazing door handles upvc doors as well as wooden and aluminium doors. They have a lever inside and a paddle on the outside and are typically available in two varieties. Sprung - These have an internal spring cassette within the backplate to help to bring the handle lever into a horizontal position. Non-sprung: These do not have a mechanism for bringing the handle lever into a horizontal position.

To repair a door handle lever that is sagging you'll need to locate the detent access pin or hole. It's usually an insignificant hole or protruding ring, or rectangle, located on the handle base plate. Once you have located the hole for accessing the detent or pin, you can take it out using the help of a screwdriver.

Once the handle has been positioned horizontally, you can put back the screws. Close them to ensure that the handle is securely connected to the base plate. You may want to apply a threadlocking solution to the threads of the screw to increase grip and stop the threads from becoming loose over time.

There are a variety of reasons that door handles for levers drop. The most frequent reason is that the fixings have been too tightened, and are putting pressure on the bearings of the lever, and causing it to pull against the door's surface. It could also be that the levers haven't been operated at the correct angle, which compresses the latch mechanism and stops it from fully springing into action.

The most common reason for a spring lever not operating properly is that the spring is not being in the proper position on the backplate. The most effective way to determine this is to operate the handle to check whether it changes to the horizontal position.

It is important to fix any loose door handles immediately. This could lead to excessive wear on the screws, and the handle could fall off the base plate. You should also tighten loose screws frequently to stop them from becoming looser.

Lever/Snib

These handles made of upvc are also known as handle sets with a 'Snib' and feature a snib button on the top of the lever that can be pressed down to lock your door if you don't use a dummy lock. They are typically fitted with a Fullex 68PZ (that's 68mm between the spindle's centre and the lever or lock centre) door lock. We also have a selection of door handles with 68PZ from brands like Ferco and Fab & Fix.

Change your door handle is an inexpensive way to update your home, whether replacing your handles or installing new ones on doors you've built in your house. There are various styles available for upvc door handles, including the traditional lever on the backplate. Other choices include straight or curved short latches as well as dummy knobs for multi-point locks. These are great for French doors.

Rose door handles are circular or oval-shaped versions of lever on backplate handles. These door handles are characterized by a lever or knob that is attached to a backplate. The backplate can be removed for hidden fixing.

There are a wide range of chrome and coloured finishes available for these handles to enhance your door and hardware, including hinges, knobs, bolts and so on. Some handles have a an grub screw that can be used to connect the knob or lever to the spindle. Other handles come with bathroom spindles that can be used to control bathroom locks and incorporate a thumbturn turn and release mechanism, which is ideal for bathroom doors.

Mortise

The tubular latch is the most likely to be the cause if your uPVC door handle is slammed shut. This can be caused by many things but the most prevalent is a lack of lubrication in the latch plate. This can be corrected quickly by opening the door and spraying lubricant on the handle and lock. It could also be that the latch has slipped away from the backplate. This could be more problematic and will require a specialist to fix.

A multipoint door handle is a great solution to solve the issue of a door handle that is stuck. These handles are mounted on the door's faceplate and are operated by the thumb turn knob or key that triggers a cam that locks the deadbolt. The handles are available in a variety of sizes that will fit various kinds of uPVC doors. They also come in an array of attractive finishes that match existing hardware. The handles are available online or from a local locksmith. They are easy to install and come with clear instructions.

If you want to replace the handle set, you'll be required to be aware of the PZ size of your cylinder. This is the distance from the edge of the inner frame of the door to the center point of the hole for the handle in millimetres. You'll also require the type of lock on your door, whether it's a mortise lock or a hook lock. The easiest way to find the right handles after you have the measurements is to use the filter for brands on the website. This will narrow down your choices and allow you to choose the appropriate size from there.

A typical handle set comes with the handle unit with a pair of various length screws drilling guides, as well as installation instructions. Smarter versions, like the Igloohome Smart Mortise 2+ include a mortice lock complete with keys. These are more complicated devices that are suited to professional installers or highly skilled DIYers. Some handle sets have a range of additional accessories, such as weather strips, which can be used to enhance the look of the door.