How to Replace a Kia Sportage Replacement Key

The key of many Kia models has the keyless entry feature built into. This key is similar to an remote control and can be exchanged by an Kia dealer.

Key fobs might stop working for several reasons, including batteries that are dead, worn buttons or buttons, water damage, signal interference and a damaged receiver module. Here are some helpful tips to assist you in getting your kia car key replacement key fob that is a replacement for the sportage for good.

How to replace the remote key or the smart key?

Whether your kia sportage key fob comes with an intelligent key, remote key push-to-start keys, or a regular non-transponder metal key, the battery in these keys will eventually require replacement. This is especially the case if your car displays a message indicating that the smart or remote keys are in poor condition.

It's a fairly simple procedure. To replace the battery on the key fob take the mechanical key from the hole in the back of the key fob. Next, remove the cover. Inside the key fob will be the small screw that holds the battery in its place. Using a small screwdriver, take the screw off and pull out the battery that was in place. Install the new battery and then close the opening on the key fob.

Once the key fob has new batteries Test it by pressing the lock and unlock buttons. You're good to go when the doors lock or unlock as expected. You can now utilize Kia's hands-free lock/unlock function whenever your fingers feel cold or you have to go on errands around Brandon.

Not all key fobs might need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder keys made of steel) don't require programming. If your keys need to be programmed, you will need to be aware of the number that is stamped on the key code tag and record it in a secure location.

How to replace a battery

If the Kia key fob is unable to respond to pressing the lock/unlock button, it's a sign that the battery is insufficient. A battery that is not functioning properly can cause other issues, like the check engine light turning on or the engine not cranking correctly. Fortunately replacing the key fob battery is a relatively simple DIY project that requires only a few basic tools.

Before beginning the process be sure that your vehicle is off and all doors are shut. Find the small, metal or plastic piece at the bottom of the key fob. Move it until the metal key comes out. This key can be placed inside the driver door handle to unlock your car.

To replace kia key fob the key fob battery, remove the cover from the back and use a pry bar tool to loosen the latch that holds the black negative battery cable. Take the old battery out, and then align the replacement battery in a way that its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place without putting too much force on it to avoid damaging or breaking the metal contacts.

After you have installed the new battery, turn the key fob off and on in the ignition until the door locks up. You can then test your kia keys made - take a look at the site here,'s key fob again to make sure it is working correctly.

How do you replace a keyless key

Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The difference between them is that the smart key has a small mechanical key blade in it, whereas the standard fob doesn't. Both key fobs have batteries that eventually require replacing. Fortunately, it's an easy process that takes only two minutes.

Before you get started it is important to make sure that you are on a flat surface with enough lighting and that your Kia is off. Be aware that the fob contains small pieces that could be thrown off if you're not careful.

The release button for the small size is located on the lower backside. This will be either a circular or rectangular slot. After pressing this button mechanical key blade, it will pop out and you will be able to open the key fob.

After the key fob has been open, remove the battery that was in it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. Once you're done with the battery, you should be able to lock and unlock your car using your key fob even if the engine isn't running!

How do you replace the mechanical key?

The Kia key fob is a fantastic convenience that lets us lock and unlock our car at the push of the button. However, like all devices it will encounter issues at times. Luckily, there are steps that can be taken to solve these issues and ensure that our key fobs are in good condition for the long run.

A dead or drained battery is one of the most frequent problems. This can cause the fob to cease working or to work intermittently. If this happens then try replacing the battery with a new one.

If this doesn't solve the issue, use the flathead screwdriver that is standard to wedge the fob's casing made of plastic open. Be careful not to damage any internal components, or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a new one.

After the new battery has been put installed, close and unlock the doors using the mechanical key (every Kia fob has an emergency mechanical key that will fit in the slot). Test the key fob to confirm it's working properly. Contact a dealer or locksmith to solve the issue in the event that the fob is not working. To avoid locking outs in the future, ensure you purchase an emergency key that will work on all trunk and door cylinders.