Reasons Your fiat bravo key 500 Key Fob Won't Work

A key fob with the fiat 124 spider key fob not Working - yerliakor.com - 500 number is a great way to unlock the doors and start the car. However, there are a variety of reasons why the fob won't be working. This could be due to a dead coin battery, damage to the receiver module, issues, or interference.

This listing is for a NEW replacement fiat 124 spider key fob cover Flip Key Remote that looks like the Ilco brand. It needs to be professionally programmed (click here to search for local automotive locksmiths). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob doesn't function is due to a dead battery. Modern key fobs come with a limited operating range and should be within a few feet of the vehicle in order to function. If you're far away from your vehicle when you press the key fob button the car won't respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery on your coin cell (Part number CR2032) with a fresh one from a trusted brand such as Panasonic, Duracell, or Energizer. You can find them at your local hardware store, or on the internet.

You can test the coin-cell battery by pressing the buttons while standing near your fiat bravo key 500. The car will blink its parking lights and the key fob will operate the lock and unlock switches.

If the key fob won't function after replacing the battery, it could be damaged by water that blocks it from connecting to the receiver module inside your car. Water damage can happen in a variety of ways, such as simply splashing or submerging the key fob saltwater at the beach. If you suspect your fob was exposed to water, put it in a dry rice bag to draw the moisture out. If this isn't working, you'll have to get your fob reset by an auto locksmith or dealer.

Water Damage

Water damage can happen if you immerse the fob into the ocean or wash it in a washing machine. Saltwater can cause the circuit board to short and eventually die. It's not a good thing to let the fob get wet, but don't give it up even if you accidentally drop the fob in water, or fail to take it out of your pocket.

First, remove the battery. Before replacing the battery clean the electronic chip with isopropyl or a similar product. Next, test the fob to see if it works. If the fob doesn't work, it may need to be reset. This is usually done by an auto locksmith or dealer.

If the key is older and hasn't been programmed to your vehicle, it will likely need to be replaced completely. This is a straightforward process that can be completed by a professional automotive locksmith. The locksmith will need the key to be cut to match the car's ignition. They'll also have to program fiat 500 key fob the fob into your car's system. This is a cost-effective and quick procedure that can be completed in the same day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote has a maximum range of 30 feet. Therefore, when you're too far from your vehicle it will not respond to your commands. It can be solved by moving closer to your vehicle until it begins responding.

If your fob won't work after replacing the battery for the coin, also called a "button", "watch" or "button" It could be due to a problem with the circuit board inside. Reprogramming your fob can resolve the issue. You can find instructions on how to do this on the majority of automobiles by searching YouTube or reading the owner's manual.

It could be necessary to replace the metal clips that hold the coin batteries in their place. If they lose tension it could prevent the coin battery from being properly seated, and this will cause the remote to malfunction.

In rare instances, the fob can become out of sync with your vehicle because due to hardware or software issues. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances the software may require reinstallation in your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This can occur when the keyfob is located in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons why the key fob might not work include a poor connection to the buttons and internal chip, or water damage.

If the key fob has suddenly stopped working, out of the blue, or after trying every option at home to resolve it e.g. You could have a malfunctioning 500 receiver module If you've tried replacing it with a battery, reprogramming, and using a spare key fob. The receiver module, which is located under the dashboard, picks up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

Fortunately, there's an easy method of resetting all of the on-board systems in your 500 keys, including the key fob. Disconnect the battery of 12 volts for about 15 minutes by taking off the negative cable first then the positive cable. Then reconnect the battery. This will remove any remaining electricity, and allow you to restart the computer in your car. This will help you get your key fob to function again. If the issue persists, you should consult an expert technician. They will be able diagnose the exact cause of problems.